15 ways to make a sharp bow and tie

How to tie a classic bow

What do you need

• Tape;
• scissors;
• double sided tape or glue-gun.

How to make bow

Place the left side of the tape to the right so that a loop.

From the left side do the same.

Put the right loop on the left.

Pull the loop, which is now located on top, into the hole from the bottom.

Pull the loop in hand, forming a knot.

Turn the ribbon so that both loops were on top, and the tips - below. Holding assembly, pull the right end of the tape. The left loop becomes smaller and neater.

Similarly, pull the left end of the tape.

Now at the same time gently pull both loops. The node will be stronger. Smooth out the resulting bow.

Fold one tip of the tape in half lengthwise. At a distance of a few centimeters from the node trim it at an angle. Scissors have to look in the direction of bow.

Likewise the other end trim strip. Glue bow on a gift.

What other options are there

Another very simple way to tie a neat bow:

If you need to do quite a tiny bow, use a fork:

Here's how to tie a bow on a gift immediately:

And if you make the top one more of the same, the packaging will look more original:

How to Tie a double bow on fingers

What do you need

• Tape;
• scissors.

How to make bow

Extend your index and middle fingers. Place the tape on top and wrap them with it.

Long right end wrap the fingers again.

The same part of the stretch between the fingers under the hinge.

Loop the ribbon down on the arm. Its tip pass through the lower loop.

Pull the tape and tighten the knot. After that will be visible shaped bow.

Remove it with your fingers. The front side is the back, so turn the bow to him. Straighten the tabs.

Trim the ends of a straight line or as in the previous method.

What other options are there

In this master class bow tie slightly differently:

How to make a bow with a stapler

What do you need

• Tape;
• stapler;
• scissors;
• double sided tape.

How to make bow

Take the tape and bend one edge to his side by a few centimeters.

Fold the strip upward around the middle of the folded section.

Hold the tape at this point, lift and remove it so that the loop to get down. If you have difficulty, see video instructions below.

From the free end of the tape at the bottom make another loop. For this perekin'te tape from the bottom to the top. Hold the bow in the middle.

Make the same way a few more loops from different sides.

Secure the ribbon stapled in the center.

Excess tip cut tape. Fold it up and fix a stapler.

Glue the piece in the center of a bow, hiding the bracket.

How to make a lush bow

What do you need

• Wide ribbon;
• scissors;
• narrow ribbon;
• double sided tape - optional.

How to make bow

Tuck the end of a wide band so that a loop. Details can be seen in the photo and video below.

Hold the tip of the tape, turn it so that it was not in the middle, and on the top edge.

Wrap the tape loop 5-6 times more. The more, the more luxuriant will bow. Excess cut.

Fold the strip in half. Incise it along the edges on the fold.

Cut a piece of thin tape, put it on the table and place on top of the folded wide tape. Pull into thin sections and tie a double knot.

Hold the tape at the center, pull to the side inner loop. Gently remove it in the opposite side from you.

Repeat the same with the next loop, pulling her in the opposite direction.

Continue pulling the rest.

Turn the ribbon and trim the tape. Bow can be glued to the present or tie for the thin ribbon wrapped around a wide belt of the box.

What other options are there

In this master class middle, the tape is cut a little differently, but still she is bound with wire, rather than a thin ribbon:

Different here loops are formed. Tape wrapped around the fingers, doing figure eights like. stretched loop is then exactly the same:

And this bow is made via plastic cable ties:

How to make a voluminous bow of the individual strips

What do you need

• Wrapping paper or tape (width of about 3 cm);
• scissors;
• line;
• pencil - optional;
• glue gun;
• cardboard.

How to make bow

Cut the paper into strips or tape. You will need four part length of 28 cm, four - 23 cm, one - 9 cm. The width should be 3 cm. It can be cut into strips of a different size, but try to keep at the same proportion.

Take one long strip and glue its edges so as to obtain the ring.

Fold the piece in half so that the seam opposite the fold. Apply glue to the fold. Attach it to the place of the seam and glue. You get "eight".

Make the same parts of the other long strips.

Cut out cardboard circle small. Put it in the center of the glue and attach one big "eight."

On her second perpendicular paste the same item.

Glue on top of the third, and then - the fourth. Arrange them so that the new loops are between the previous ones.

Four "eights" smaller stick in the same way. Each of them should be placed parallel to one of the larger pieces. The video detail below shows the whole process.

The last small strip of glue in the ring, and attach to the middle bow. The finished dressing stick to the present.

How to make a voluminous angular bow

What do you need

• Wrapping paper or tape (width of about 2 cm);
• scissors;
• line;
• pencil - optional;
• double sided tape.

How to make bow

Cut the paper into strips or tape. You will need three pieces of 20 cm long, three - 15 cm, one - 7-8 cm. The width should be about 2 cm. You can use other sizes, but try to keep the proportions.

Glue to the edge of one long piece of adhesive tape strips from the back side. Fold the edge, as shown in the photo.

Then glue edge to the front side of the strip. You will get something like a cone.

Repeat the same on the other side of the strip. Thus glue remaining five long parts. The shortest will need later.

Glue the large items on top of each other so that all corners looked in different directions.

Glue on top of the other three parts. The corners of each new strip must be placed between the corners of the lower parts.

Glue the short edge of the strip and paste the resulting ring in the middle of the bow. Attach the ribbon to the present.

What other options are there

Resembling the bow can make one tape with a special homemade tools: