How to clean a toilet from urinary stone, limescale and rust

Why do urinary stones, limescale and rust appear on the toilet?

Different types of pollution occur for different reasons.

So, limescale appears due to the accumulation of minerals. This problem often occurs in houses with hard water. Typically, yellowish streaks form on the toilet at the flush point, but can also occur on other parts of the plumbing.

Urine stone consists of calcareous and mineral deposits. It not only spoils the appearance of the toilet, but also emits an unpleasant odor. Most often it occurs where people forget to flush the water after visiting the toilet or rarely wash the plumbing with special products.

Rust appears mainly due to old and poor-quality pipes, not only in the house itself, but also in the general water main. Over time, the metal corrodes, and fragments of oxidized iron enter the water, which settle on the surface of the toilet and color it red. However, the problem can also arise in a high-quality pipeline, when the water itself contains a lot of iron.

The material of the toilet bowl also affects the rate at which contaminants form. For example, sanitary porcelain has a denser structure, its surface remains smooth longer, and therefore less plaque deposits on it. Earthenware is less dense and is not as resistant to mechanical damage. Sediments eat into microcracks and rough surfaces faster and deeper.

How to clean a toilet from urinary stone, limescale and rust

These products will be equally effective against all of the listed contaminants. If you need to clean the walls of the toilet drain, first pump the water out of it using a plastic bottle or scoop it out with a small glass.

Using dishwasher tablets and citric acid

Place 2 tablets in a container with a volume of at least 1 liter. dishwasher and add 30 g of citric acid. Add 700 ml of hot water and thoroughly dissolve all components in it.

Wear rubber gloves. Using a sponge or rag, apply the solution liberally to the dirty surfaces of the toilet. Leave the mixture to work for about an hour. Then wipe off the limescale, urinary stone and rust with the rough side of the sponge. Flush the toilet.

Using citric acid and mustard powder

Pour 2 heaped tablespoons of citric acid and mustard powder into a small container. Gradually add warm water to form a thick paste. The consistency of the product should resemble thick sour cream.

Wear rubber gloves. Using a dishwashing sponge, apply the mixture to the surface of the toilet and leave for an hour. After this, clean the plumbing with a brush, and then flush the water twice.

Using vinegar essence and dishwashing detergent

This product will be quite aggressive, so wear rubber gloves before working to protect your skin.

Take a plastic or glass container with a volume of at least 500 ml. Pour 160 ml of vinegar essence (80%) into it. Add 50 ml of dishwashing detergent (it can be replaced with liquid soap) and mix the ingredients thoroughly.

Using a brush or brush, apply the product to the surface of the plumbing fixtures. Leave for 30 minutes. After this, clean off any remaining dirt with a brush and flush the toilet.

Using ammonia and hydrogen peroxide

Before preparing this product, wear rubber gloves and a respirator to avoid harm to your health.

Pour 1.5 liters of warm water into a plastic or glass container. Add 40 ml ammonia (10%), 100 ml hydrogen peroxide (3%) and stir.

Pre-pump out the liquid from the drain hole. Pour the prepared mixture into the toilet and use a brush to apply it to all contaminated surfaces. Close the lid and leave the solution to act for 3 hours. After this, thoroughly clean the surface with a brush, especially paying attention to areas with plaque, stone and rust. Drain the water 2-3 times and ventilate the room.

Using vinegar and iodine

This product will cope with limescale, urinary stone and rust in the toilet drain hole. Before use, do not forget to pump out the water from there.

In a small saucepan, heat 250 ml of vinegar (9%) to a temperature of 40–50 degrees: the liquid should become warm, but not scalding hot. Remove the dishes from the heat, add 3 tablespoons of iodine and mix the ingredients thoroughly.

Pour the solution into the drain hole, close the toilet with a lid and leave everything for 3 hours. After this, scrub the stains with a brush and drain the water twice.

Using household chemicals

Special products effectively remove dirt and save time. They are sold in powder, gel, liquid or cream form. Depending on the type of product and manufacturer, methods of application may vary, so first carefully read the instructions on the package. As a rule, the compositions work on approximately the same principle: you need to apply the product to the surface of the toilet, leave for a while (from a couple of minutes to an hour), remove dirt with a sponge or brush and rinse water.

Since household chemicals can be quite aggressive, wear a respirator and gloves when working with them.

How to prevent stubborn stains on your toilet

• Keep it clean. At least once a week, thoroughly clean the toilet using special products.
• Try toilet flush tablets, toilet freshener blocks and gel stickers. They not only eliminate unpleasant odors in the restroom, but also help prevent the appearance of complex stains. Such products contain components that soften water and disinfect the surface of plumbing fixtures.
• Follow serviceability of the toilet. If the cistern is constantly leaking, rust and limescale will certainly settle on the walls.
• As cliché as it may sound, flush after every use of the toilet. And if there are small children in the house, make sure that they do not forget about this.

We read an example: “She almost croaked, but, fortunately, she remembered that it was already autumn and that frogs don’t croak in autumn...” V. Garshin, Frog-traveler. It turns out that Garshin is happy for the frog here and imposes this joy on the reader?

7 of the strangest CIA covert operations in history