How to make a swing with his own hands: 10 cool options

1. Classic swing out of the board

What do you need

• Thick rope;
• 30-50 mm thick board;
• drill;
• drill;
• hacksaw;
• paint;
• brush.

How to do

1. Cut a piece of board length of about 50 cm with a hacksaw or other saw, which is handy.

2. To protect against rain and to give a more aesthetic appearance of the resulting color seat.

3. drill a couple of millimeters greater than the thickness of the rope used, perform two holes - at both ends of the board. Stand back from the edge of 2-3 cm, so that the seat is not broke, and drill the exact center of the vertical for a smooth suspension.

4. Divide the rope into two equal parts, take the ends of the loop and secure the appropriate branch. Place the rope at a distance approximately equal to the seat width.

5. Thread the ends of the rope in the hole board and tie a pair of nodes by choosing the desired height.

6. Try to swing.

What can be changed

• If you do not have the board, as the seat is suitable handle of a shovel, a piece of wood or a piece of plywood.

2. Swing from the disc and one rope

What do you need

• 4-5 boards 30-50 mm and a length of 400-500 mm;
• thick rope;
• hammer;
• nails;
• brush;
• paint or varnish;
• clamps;
• glue;
• drill;
• Drills on a tree;
• roulette;
• thread;
• pencil;
• jigsaw;
• sander or sandpaper;
• file.

How to do

1. Pitch of pad boards. To do this, smear the ends of the adhesive side, connect together, and tighten clamps. A simpler variant: Nail the two bars across planks, departing from the edge by 10 cm.

2. Grind the upper part of the site by hand with sandpaper or by machine.

3. With a tape measure and mark with a pencil the center of the site. Also, put a line at a distance of 10 mm from the edge of one of the parties.

4. Hammer a nail into the center, tie a string to it and a pencil draw a circle radius with a length of label from the pad edge. Pull the nail: it is no longer needed.

5. Saw jigsaw circle and then align the sharp edges with a file or sandpaper.

6. Perform drill hole in the center of 2-3 mm greater than the thickness of the rope swings future.

7. Files grind off the sharp edges formed in the center, not the rope swing at peretorsya.

8. Paint or cover the resulting varnish seat and wait until everything is dry.

9. Thread the rope through the hole and tie a couple of knots to keep it from sinking.

10. Attach the free end of the rope on the tree.

What can be changed

• Round seat easily replace strong enough rectangular board. Riding on this did not worsen.
• In order not to mess with the merging of the boards, it is possible to take an appropriately sized piece of plywood.

3. Swing from old tires

What do you need

• tire;
• bicycle inner tube;
• rope;
• insulating tape;
• diameter steel washers rope;
• staples, clips;
• drill;
• drill;
• knife;
• a thin wire or fishing line.

How to do

1. Estimate the approximate length of the rope that was enough from the branch to the ground, and add 1 m in reserve.

Rewind the tape in the right place, the edges are not disheveled, and separate the piece with a sharp knife.

2. Cut cycling chamber and put on one end of the rope.

3. Tie this part so as to obtain a loop wrapped chamber. This protects the rope from abrasion and will not give it to crash into a branch.

4. Sling rope over a branch and then tighten it. For convenience, you can use a thin lace with a small weight attached to it.

5. Form a knot at an altitude of about 1.5-1.7 m from the ground.

6. More Cut two pieces of ropes about 2 m in length each. Pass them on the suspension assembly, and then tie at their ends on one node for fixation.

7. Tighten the knot on the main rope from the branch. You should have three ends, which will hold the tire.

8. Divide the tire into three approximately equal parts and drill holes with a diameter over the thickness of the rope, departing from the edge of the tire. With its back side to make several holes for drainage rainwater.

9. Insert the rope in the hole, put the washer and secure the ends with clips.

10. Release the bus and try to swing.

What can be changed

• Instead, you can simply clamps to fasten components, which will not allow the rope to sink into washers and will safely hold the entire structure.
• If desired, the bus is easy to paint to make it look more aesthetic and does not stain clothes.

4. Swing from boards

What do you need

• A piece of furniture board;
• square;
• pencil;
• rope;
• drill;
• drill;
• file;
• emery paper or plane;
• hacksaw;
• matches or lighter.

How to do

1. Stand back from the edge of the furniture board 250-300 mm, attach the square and draw a pencil line.

2. Hacksaw cut off a line of the future seat of the swing.

3. Schedule pencil space for mounting the rope at each corner, departing from the edges 20 mm.

4. Make drill holes. The diameter of the pick such that the ropes go to work and not loose.

5. Spilite sharp corners plank hacksaw, and then grind off a file. If you want to get the accurate, first mark the form of patterns, coin or other round object.

6. The upper edge of the board chamfer sandpaper or a plane to child not injured.

7. Cut two identical pieces of rope and prizhgite their ends.

8. Thread the rope through the holes in the board on each side so that the free ends were on top.

9. Fasten the ends of the ropes on any solid support, such as beam wall bars.

What can be changed

• If the wood panels replace cutting board, it will only drill the holes and fix the ropes.
• Swings can be hung in the doorway, in a tree, on a beam or a terrace pergola.

5. Swing polypropylene tubes and plywood

What do you need

• Polypropylene tube;
• rope;
• plywood;
• carbines;
• hacksaw;
• cutter;
• drill;
• drill;
• paint;
• brush.

How to do

1. Cut out of plywood size of 30 × 30 cm seat or 30 × 40 cm. Drill holes at the corners for attaching ropes. cover with plywood painted if desired.

Slice polypropylene Pipes on the part of 15 cm - four pieces, 25 cm - two pieces, 35 cm - two pieces. Drill each interval through holes on both edges.

Divide the rope into two equal pieces. Then, each fold in half, insert and fasten in carbines. This will be the left and right suspensions.

2. Take the longest length of pipe and thread the rope on one of right and left hangers into the holes on each side.

3. Following nanizhite one middle segment of the tube, inserting the same rope through holes at the ends of parts.

4. Then - one very short piece. Here the rope is inserted into the pipe itself, along the entire length.

5. Now through the openings of the second long segment of thread free ends of the left and right suspensions.

6. Stick rope in the remaining free openings in the tubes of medium length. And then add one short piece, again skipping rope through the tube throughout its length.

Pass the free ends of the hangers in the back holes and fasten to each of them host.

7. Attach the hooks on any solid support. Swing ready!

What can be changed

• The seat also easily make cutting of boards or pieces of wood of appropriate size.
• Instead of pipes will fit wood or cuttings from the garden tools. True, it is necessary to tinker with drilling holes for the ropes.

6. Swing from a skateboard

What do you need

• Old skateboard;
• rope;
• handle of a shovel;
• roulette;
• pencil;
• drill;
• drill;
• paint;
• screwdriver.

How to do

1. Remove the wheels from the board and all unnecessary.

2. Back down to 5 cm from the edge and put the check marks for the four holes for the ropes: two on each side.

3. Drill through these places. Diameter adjusted so that the rope is kept as tight as possible.

4. Cut two pieces of stalk from 30-40 cm long and drill therein by one hole on each side. Stand back from the edge of 3-5 cm, so that the wood is not cracked. This will be the palm rest.

5. Color bars of color skateboard.

6. Divide the rope into two equal pieces and fold in half. At each end of tie knots, but do not tighten tight.

7. Thread the rope through the bars, do more for the node, and then - Miss rope through the hole in the skateboard. Tie bottom at the free ends of the board nodes.

8. Suspend the structure on the relevant branch wood and using the units, adjust a comfortable position handles.

What can be changed

• If you make a single thicker suspensions with a split in the skateboard, you can easily do without handles.

7. Swing with the supports and the purchase Seats

What do you need

• Board 50 × 200 mm;
• board 25 × 100 mm;
• Anchor bolt 2 with rings;
• 2 carbine;
• timber 50 × 100 mm;
• nails;
• seat swing;
• hammer;
• roulette;
• drill;
• drill;
• hacksaw or jigsaw.

How to do

1. Cut the parts necessary for the assembly of two poles, four pieces of 2.5 m from the board 50 × 200 mm, four - of 1.35 m from the board 25 × 100 mm, and four - 35 cm from the beam 50 × 100 mm.

Collect the structure in the form of the letter "A". Fold the long board at an angle and nail them with nails jumper from the middle segments. Reinforce support the top of short pieces of lumber.

Similarly, the second support Pitch swing.

2. Cut off the protruding edge of a saw or jigsaw to avoid injury.

3. On the cross member at the top of the letter "A" put a piece of board 200 × 50 2 m and nail. Lift the entire structure.

4. Middle beams drill holes for fastening at a distance of 50-70 cm from each other. Wrap them in the anchor bolts with rings.

5. Hang seat on the ropes and secure with the rifles on the rings.

6. Check structural strength.

What can be changed

• Instead of boards of supports can be used round logs or timber.
• Purchase seat easily replace home-made.

8. Swing from the chair

What do you need

• Chair;
• rope;
• paint;
• brush;
• hacksaw;
• drill;
• drill;
• emery paper.

How to do

1. Cut the legs of the chair with a hacksaw at the very back.

2. Make drill one hole in each corner of Seats.

3. Sand surface chair sandpaper.

4. Cover the resulting seat swings fresh coat of paint and let it dry.

5. Divide the rope into four equal parts. Pass each piece into the hole and fasten a pair of nodes.

6. For loose ends hang structure to a thick branch of a tree.

What can be changed

• Swings can be hung on the terrace or in the gazebo. Especially cool is to build several of these structures and relax together with friends.

9. Swing from the tray

What do you need

• Pallet;
• rope;
• emery paper or machine;
• Scotch;
• carbines;
• drill;
• drill;
• scissors;
• lighter.

How to do

1. Grind the surface of the skin on pallets or machine, to remove any burrs.

2. Drill outer boards of the pallet of six holes with a diameter equal to the thickness of the rope.

3. Turn the pallet and do the same with the other side. Try to keep the holes in the top and bottom boards were under each other.

4. Go through holes sandpaper or machine to remove burrs or damage the rope.

5. Prepare two pieces of rope. wrap the rope scotch tape and cut at this point. Then cauterize that the edges are not disheveled.

6. Pass the rope snake holes from one pallet edge and tie knots on the ends.

7. Do the same with the other side of the pallet.

Straighten the rope, turned to similarity of ropes hanging bridgeAnd connect the carabiners - one on each side.

8. Take two more pieces of rope and tie them around the loop at both ends.

9. Sling the ropes through a thick branch of a tree.

10. Hook the tray to the suspension with carbines.

11. Spread a blanket and bring a pillow.

What can be changed

• Instead of the top rope suspensions easily make circuits. Supporting cables can also be replaced by chains, but it would look too brutal.

10. Garden swings with legs

What do you need

• Beam 100 × 100 mm;
• timber 50 × 50 mm;
• galvanized chain;
• board 25 × 100 mm;
• screws;
• mounting plate;
• screws;
• sandpaper;
• hacksaw;
• jigsaw;
• roulette;
• pencil.

How to do

1. Because timber 100 × 100 mm cut four strut height 195 cm.

2. Collect the two supports in the form of the letter "A" with the top and bottom struts of the timber 50 × 50 mm. Details drilled through and bolted.

3. Cut the timber 100 × 100 mm crossbar length of 1.8 m and secure the abutments on the upper rack by pulling bolts.

4. File off six boards of 120 cm length: three for the back and three more - for the seat.

5. On the top board back, if desired, cut out jigsaw pattern. Good grind everything with sandpaper.

6. By timber pieces of 50 × 50 mm screws, attach the three boards - it will seat.

Do the same for the back, and connect the two parts together at the desired angle.

7. Saw two armrests boards and fasten them with screws through the bar to the seat and backrest.

8. Drill in the beam bolt holes and install it, having passed through the chain link. Top lock nut, and that it does not fell a tree - enclose a metal plate or a large diameter washer.

9. Make a hole in the rod seat, insert the bolts and secure the ends of the chains.

10. Adjust the length of the suspension desired position.

What can be changed

• For greater strength, you can add another cross beam on the bottom of the back of the legs.
• Optionally Construct visor made of polycarbonate or tarpaulin to protect from the sun and rain.