How to install the faucet with their hands

How to install the faucet on the sink

1. Prepare materials and tools

• Mixer with mounting hardware;
• 2 flexible liner;
• rags;
• masking tape;
• adjustable wrench.

2. Shut water

Before you start to work, close the valves and cold hot water on the sink. If a separate shut-off valves on the device is not present, turn off the water in the riser.

Bed bowl clean cloth so as not to damage the coating accidentally fallen parts.

3. Remove the aerator

Remove the aerator from the spout so that it is not clogged with rust and other contaminations from the pipe. To do this, unscrew it counterclockwise plastic key of the kit or a conventional weir.

Sponge metal key can scratch coating mixer, so better wrap them masking tape or cloth.

4. Assemble the mixer

Typically, the plumbing is delivered already assembled. If some of the elements are not attached, install them according to the instructions. Take the mounting pin from the set screw and clockwise to lock into the hole of corresponding diameter in the lower part of the mixer.

5. Connect the flexible hoses

Attach flexible fittings podvodok to the mixer by tightening them by hand. Pre-check that the ends of the thread set seal rings. Do not screw fittings key - excessive force may damage the gasket.

6. Install the valve in place

That water does not leak to the body, put the seal ring in a groove at the base of the mixer.

Pass in the first mounting hole washbasin single hose flexible liner and then - the second. Place crane in the space provided.

7. Attach the mixer

Move under the sink. Put on the rubber gasket on the studs and the retaining washer in the form of a crescent. Screw the top nut and tighten it by hand, and then tighten the Allen key.

Before final tightening make sure that the mixer is set at an angle.

8. Connect to the water supply

Now put on vodorozetok fittings or valves union nut shell podvodok flexible and tighten them by hand. Tighten the key compounds, but not much - just be half a revolution or a little more.

Do not confuse the hoses! According to the standard hot water should be on the left and cold - on the right.

9. Check the operation of the mixer

For checking and flushing the system from possible contamination, open the shut-off valves on the device or risers. Let the water and make sure that when you turn the faucet hot and cold flow as it should.

10. Install an aerator

Replace the nozzle by turning it into the mixer by hand in a clockwise direction. Quite a bit, tighten the aerator plastic wrench or an adjustable usual. In order not to scratch the chrome coating, sponge key can wrap masking tape.

How to install bath mixer

1. Prepare materials and tools

• Mixer;
• watering can For shower hose and bracket;
• eccentric sleeve with spacers;
• decorative rosettes;
• FUM tape;
• plugs;
• silicone sealant;
• masking tape;
• spanners 22 mm and 32 mm;
• wrench;
• level;
• roulette;
• pencil;
• drill;
• drills on ceramics and concrete.

2. Shut water

To start disconnect water supply in a house using cranes riser hot and cold water. Then check that the tubes really nothing.

3. Remove the aerator

Prior to installation of the mixer in the tubes may be rust and dirt, which are capable goal reticulum aerator. Therefore, it is better to remove: remove the special adaptation of the kit or a conventional wrench jaws wrapped with masking tape.

4. Try mixer

Take the eccentric sleeve from the kit and thread them into the vodorozetki wall. Screw fittings four to five turns so that the distance was 150 mm between their centers.

Screw the top decorative rosettes, and then set the mixer and tighten by hand the union nuts. Make sure that between them and the pair remains capped threads.

Check the bubble level, even if the design is set, and if necessary, adjust its position by screwing or unscrewing the eccentrics. Measure the exact distance that the sleeve protruding from the wall, and remember it.

5. Set eccentrics

Disassemble the entire structure to collect was finally sealed with a screw. Wrap thin ends of eccentrics five or six turns of the tape FUM-clockwise. Screw couplings at the wall to a depth measured previously.

6. Seal the joints

So that the water does not leak into the gap between the eccentric and wallFill it with silicone sealant. Extrude the desired amount from the tube and gently smudge around the joints.

7. Set the mixer

Screw the decorative rosettes on the eccentrics. Install the gaskets in the union nut of the crane, and then attach it to the coupling and tighten the nut. First by hand, then with a wrench by about one turn. Check the level that the mixer is installed horizontally.

Wrap sponge key masking tape so as not to damage the coating on the nuts mixer.

8. Attach showerhead

Place the gasket in the cap nut of the hose and wind on the part corresponding to the union on the mixer. Second, the tapered end of the tube to attach the funnel, also do not forget about laying.

9. Secure the bracket to watering

Estimate, at what height will be located holder for the shower. Glue in this place the masking tape, and then attach the bracket and mark with a pencil point to mounting holes.

Drill the holes. First Ceramic drill in tileAnd then drill in concrete - in the wall. Insert the dowels into the holes and secure with screws holder.

10. Check the operation of the mixer

Open valves in the pipework of hot and cold water. Make sure that the mixer operates in all modes, including a shower.

11. Install an aerator

After the merge small amount of waterDo not forget to return to the place of attachment of the mixer. Screw the aerator by hand and tighten to 10-20 degrees special plastic wrench supplied. If no such tool, wrap the sponge wrench masking tape and use it.