How to iron complicated things without pain

How to prepare a place for ironing

Virtuosos can get the perfect result and on a table covered with a blanket, but it is better to have an ironing board. Right-handed it is necessary to establish a rounded end to the left, left-handed, respectively, to the right. The light should fall into the workplace by less active hands, cord - free to follow for iron and not interfere with stroking.

At hand's good to have a special gauze or cloth ironing, water tank. As a rule, modern irons are equipped with sprinklers, but the spray will moisten thing much faster.

How to iron clothes

shirts

Shirt for a good result should not be dry. Before ironing sprinkle it with water from the sprinkler.

Begin ironing a shirt with a collar. With iron its inside, then the outer side. The next stage - the cuff. They should undo and spread on the ironing board, then carefully to iron. Then move on to the sleeves. They should not be the shooter. You do not accidentally make amends for them, pass the iron only in the middle of the sleeve, avoiding the fold of fabric.

In the last floor and stroked the back of his shirt. Pay special attention to the portion where the shattered hinges - after zastogivaniya buttons it will be on top.

Pants

Remove the pants inside out and flatten the seams and pockets. Further manipulations are carried out from the front. That on his pants did not appear shiny areas, use moist gauze. It will quickly dry from the heat of the iron, so keep a container with water.

Put one leg on a board, cover with gauze and iron from the bottom up.

Be careful so that no wrinkles, get rid of them will not be easy in the process.

Then enjoy a riding pants, for convenience they can pull on the rounded edge of the board. Pay particular attention to the folds at the waist, if they exist.

The last stage - smoothing the shooter. Align the side seams of trouser legs and gently through cheesecloth iron the cloth folds. This activity requires concentration as sloppy hand looks more sloppy than its absence.

jackets

Because of the many joints and parts jacket or cardigan is also better to stroke through cheesecloth, so that the fabric is not zalosnilas. First otutyuzhte sleeves, then enjoy a shrug. Facilitate the task, you can use the roller from a collapsed tight towels. Put it in the sleeve to smooth out the arrow, and a shoulder to to iron the seams.

The back and shelf and ironed on the front side through cheesecloth. With jacket problems should arise, and the jacket will require special attention because of the darts on the chest. Keep the shelves were not formed folds, if they are not provided for the designer. "For breakfast" remain collar and lapels. To them it was easier to iron, in the course of a little pull the fabric by hand.

Knitwear

For knitwear should be treated with more attention during the drying process. Items of this material is best to dry the straightened on a horizontal surface: then may not have their stroking. When knitwear still need ironing, moisten with water and gently thing otparte. Actively drive the iron is not necessary, just apply a hot sole instrument to each site and things linger in this position for a few seconds. So you do not deformiruete jerseys.

delicate things

Products made of thin fabric better ironed from the inside at the lowest temperatures. First, try to iron things land, which is not in sight: so you will understand how the fabric will behave after contact with a hot surface. You can also save a piece of cloth, which are often sewn to the product, and train ironing delicate fabric on it.

How to iron home textiles

Fitted Sheets

Iron sheets with an elastic band around the perimeter - the test is not for the faint of heart. It is unclear how it folded and placed on an ironing board.

To iron sheet can be immediately prior to use. Pull her onto the mattress and walk on her iron. If the question of storage ironed linen of principle, it is possible to iron the sheets on the mattress, then gently fold. Fold it in half and fill one corner to the other on each side, and then - again in half to all the corners are aligned. Spread the resulting rectangle on the table and fold as traditional sheet.

duvet Covers

Fold duvet cover four times. Iron it on one side, turn over and repeat the procedure. Expand the duvet cover and fold again so that neotutyuzhennye sides were on the outside. Again, iron it on both sides. Repeat until the entire fabric is not straightened.

Silk bedding

Silk is best ironed inside out to avoid damaging the delicate tissue. Be sure to save the labels that say what the temperature conditions when ironing the manufacturer recommends the use of the product, and clearly follow these tips.

Silk underwear is not recommended to sprinkle water during ironing: can remain divorces.

If you need to moisten the thing better sprinkle it with an atomizer and put an hour in a plastic bag. Since the product is uniformly impregnated with moisture.

tablecloths

First otutyuzhte edge only then go to the central portion. If the product is strongly retain moisture, sprinkle it with an atomizer and fold into a roll to moisten it evenly. For cotton and linen tablecloths use hot water, it absorbs the fabric better.

blinds

Curtains need to stroke, when they are still wet. Start ironing the curtain from top to bottom. When the upper edge of the sink and ironing board almost to the floor, hang the curtains on the ledge. Continue stroking bottom, smoothing it on the board. So you can avoid wrinkles and tissue contamination. Pelmets and utyuzhat wet.

For synthetic fabrics have life hacking, which will altogether dispense with the iron. Wet curtains hang on the ledge - they smoothed under its own weight.

How to iron things that can not be ironed

If the label on things explicitly prohibits contact with the tissue iron, but the folds and creases somehow smooth need, there are two ways to solve the problem.

1. Valet "obstacles"

Need four dense tissue. Moisten the two of them. Fold the "sandwich": wet wipe, dry, and then crumpled thing, then again dry and wet cloth. Low hot iron progladte structure.

2. steaming

Hang the product on a hanger or lay out on the board. Hold the iron in tissue, but does not touch it with a red-hot surface. Check the device in advance: with the steam it can start spewing chunks of rust. Press the steamer button for as long as the thing does not become slightly damp. Then let it cool and dry.