How to clean iron at home

After buying iron for long pleases us with brilliance and clarity. Pat the silk blouse at wrong temperature - hi, metal penetration. Water poured from the tap - hello scum. Nine ways for everyone to help return the original appearance of the device. Tips on how to avoid problems in the future, are included.

How to clean the iron metal penetration

Before you begin cleaning iron, determine which method is suitable for your equipment. Ceramic or Teflon sole, for example, can not rub abrasives. Use of sparing methods mentioned below.

Method 1. Salt

Pour onto a paper sheet salt evenly and drive over it with a hot iron, not descend until black.

Method 2. paraffin candles

Candle wrap cotton cloth and rub in a circular motion red-hot soleplate. Hold the unit layer or above the tray newspapers: during candle will melt the wax will flow downward.

Be careful, if the working surface of your iron embossed or has openings for the pair. Paraffin can get into the recess and in the subsequent ironing stain your clothes.

After defeating Prigara carefully remove any excess dirt and molten candle.

Method 3. Hydrogen peroxide

Moisten a 3-percent hydrogen peroxide, a cotton swab or a piece of cloth. Carefully and with an effort to scour the dark spots on the surface of cold iron. Peroxide will help dissolve plaque and facilitate its removal.

Method 4. vinegar

Moisten a cotton ball in vinegar and wipe the soles of cold iron. If burn-strong, add the vinegar, ammonia in a ratio of 1: 1.

If this does not work, soak the cloth in vinegar and cover its working surface of the device for a few hours. During this time, plaque softened. Remove it with a sponge or soft brush.

Method 5. Baking soda

Dissolve several spoons soda in a glass of water soak in this solution the piece of material and wipe them cold surface of the iron. At the end of the iron clean damp sponge divorce.

Method 6. Nail polish remover

If the soleplate is stuck to a piece of polyethylene, it can be removed with liquid nail polish remover. When cleaning, be careful not to touch the plastic parts of the iron: the substance as part of the liquid can damage them.

Never use for cleaning iron nazhdachku, knife or other sharp objects! This scratch sole and can lead to malfunctions of the device.

How to prevent the formation of metal penetration

To burn-never appeared, follow these simple tips:

1. Observe the temperature settings for each type of tissue.
2. Particularly delicate items such as hair, ironed through damp cheesecloth.
3. After each ironing, wipe the surface with a soft cloth iron.

How to clean iron from scale

If you become a bad run supply function coupleAnd iron reserves on clothes red spots, most likely it was formed in the scale. Delete it without help balance the three win-win recipe.

Method 1. Self-cleaning function

In many modern models of care about the problem of scale manufacturer. If you are not sure of the appointment of some of the buttons on your unit, check the instructions: You might be lucky enough to own an iron with self-cleaning function. To perform it, carefully follow the manufacturer's advice. In short, the algorithm is as follows:

1. The tank is filled with the greatest possible amount of water.
2. The temperature controller is set to maximum.
3. The device heats up, cools, heats up again.
4. Iron bends over a bowl or sink.
5. After pressing the self-cleaning button scum derived from the steam holes in the sole.

After the procedure, wash basin with clean water several times and wipe dry iron.

Method 2. Lemon acid

Tablespoon (20-30 grams) of citric acid dissolve in a glass of water and pour into the tank. Heat the iron to maximum good shake a few times, and then press the shutter button pair. Perform this procedure over a sink or capacity: scale will be published together with the steam hot dark spray. After the wash basin with clean water and wipe the soleplate from dirt residues.

Method 3. Carbonated mineral water

The carbonated beverage composition comprises acid that will dissolve the pellet in the iron. Just pour mineral water into the tank and follow the instructions of the preceding paragraph.

How to prevent the formation of scale

It was not necessary to remove scale in the future, monitor the quality of waterYou fill up the iron. This is best suitable:

1. Distilled water: is on sale at any gas station.
2. Bottled water from the nearest supermarket.
3. Water treated with a home filter.
4. Settled tap water: a few hours of salt will fall into the sediment.

And you have your secrets cleaning household appliances? Share them in the comments!